设为首页 | 加入收藏 | 联系我们
产品分类
当前位置:首页 - 新闻动态-公司新闻
新闻动态
联系我们
济南华政印务有限公司
地址:济南市历城区工业北路161-1号华政印务
电话:0531-88771456
手机:13698644688
邮箱:371162023@qq.com
传真:0531-80992585
联系人:万经理
印刷不上墨的问题你经历过吗?
作者:admin 来源:http://www.sdhzyw.com 发布时间:2019-5-7 14:08:16 浏览次数:443
提到印刷不上墨,应该是每个印刷厂都会遇到的问题。操作人员关于不上墨的态度普通就是“没有方法了,就这样用吧。”当然是在概率比拟低的状况下。假如频率比拟高,印不出活件,影响开机产量了,那就倡议换机台印刷。当时看似“处理了问题”,但是过一阵子问题又频繁发作。所以今天济南宣传单页印刷厂家要来讨论一下不上墨问题的成因和处理办法。
When it comes to printing without ink, it should be a problem that every printing factory will encounter. Operator's attitude about not being able to ink is usually "no way, just use it." Of course, in the case of low probability. If the frequency is comparable to high, and no movable parts can be printed, which affects the start-up output, then it is advisable to change the printing table. At that time, it seemed to have "dealt with the problem", but after a while, the problem recurred frequently. So today Jinan Publicity sheet printing manufacturers want to discuss the causes and solutions of the problem of not ink.
1.开机就发作不上墨
1. Turn on and you won't get ink.
假如刚上机就发作不上墨,处置办法可用洁版剂来擦拭,假如擦拭后就没有问题了,这个属于浮脏惹起,普通和印刷没有关系。
If you can't get ink on the computer, the disposal method can be wiped with detergent. If there is no problem after wiping, it belongs to floating dirt, which has nothing to do with printing.
成因:浮脏,检查冲版机水洗和上胶局部,如水洗毛刷能否有凝胶,由于环保压力下,很多客户曾经把水洗改成自循环,为了避免发臭,常常会参加添加剂,一朝一夕便会有赃物混入版面,另外检查维护胶能否有按正常的比例,普通重新清洗水槽,改换维护胶便可处理。

Causes: floating dirty, check the washing machine and glue parts of punching machine, such as whether the brush can be gelled, because many customers have changed the water wash into self circulation under the pressure of environmental protection. In order to avoid stinking, they often participate in the additives. Overnight, there will be stolen goods mixed into the layout. In addition, check whether the maintenance glue can be kept in normal proportion, clean the sink again, and change the maintenance glue. Handle.

济南宣传单页印刷产品

2.印刷到中途呈现毛病
2. Faults in printing
开端还比拟正常,但是中途就逐步发现某一个颜色变浅,查看印张和版材,印张上面特别是在实地块的边缘局部,发作相似掉网的磨损。但是用洁版液擦拭版面后发现药膜层还是存在的。这个时分就需求查看不上墨的位置,判别能否属于咬口或者版尾由于机械压力不均,磨损毁坏了药膜的砂目,招致砂目无法支撑足够的油墨的粒子,从而形成油墨无法传送。但是假如整个版面都存在,且无规律可循,那么就需求检查润版液的参数或者品牌能否会和油墨及版材发作“不匹配”。由于油墨的黏性和流变性,水斗液的张力控制都会影响到版面的水墨均衡。由于版面的亲墨层还在,阐明是属于有非亲墨的物质附着上面了,普通用洁版剂擦拭后,可暂时印刷几百张,但是不久后又开端发作。倡议更好还是彻底清洗水箱,清洁水墨路,重新分配水箱参数,是能够处理的。
At the beginning, it is comparable to normal, but in the middle, it is gradually found that a certain color becomes lighter. Look at the printed sheet and plate, especially at the edge of the real block, there is similar wear and tear. But after wiping the plate with the cleaning solution, it was found that the film still existed. At this time, it is not necessary to check the position of the ink, to determine whether it belongs to the bite or the end of the plate due to uneven mechanical pressure, wear and tear the sand of the film, resulting in sand can not support enough ink particles, thus forming ink can not be transmitted. But if the entire layout exists and there is no rule to follow, then it is necessary to check whether the parameters of the embellishment solution or the brand will "mismatch" with the ink and plate. Because of the viscosity and rheology of the ink, the tension control of the bucket fluid will affect the ink balance of the layout. Since the ink-affinity layer of the layout is still there, it is clarified that it belongs to the non-ink-affinity material attached to it. After wiping with a general detergent, hundreds of copies can be printed temporarily, but soon it starts to break out again. It is advisable to thoroughly clean the water tank, clean the ink circuit and redistribute the parameters of the water tank, which can be handled.
以上是以毛病发作的时间来查找问题所在,那么假如时间是不定时的发作,机台和所用资料之间也没有明显的规律,还是时不时的一宗毛病,可能这才是实践印刷消费中遇到的问题。
Above is to find out the problem by the time of the occurrence of the problem, then if the time is an irregular occurrence, there is no obvious law between the machine and the data used, or a fault from time to time, this may be the problem encountered in the practice of printing consumption.
其实经过以上剖析能够理解到,“不上墨”并不是难以处理的问题,主要是先分分明不上墨发作的时间段和找出资料匹配方面的规律,问题自然迎刃而解,而标准地控制好印刷各个环节可能呈现的问题就至关重要了。
In fact, through the above analysis, we can understand that "no ink" is not a difficult problem to deal with. It is mainly to clarify the time period of no ink onset and find out the law of data matching. The problem will be solved naturally, and it is crucial to control the problems that may appear in all links of printing.
以上的精彩内容由济南宣传单页印刷厂家整理提供,希望对大家有所帮助!更多精彩内容欢迎关注我们的官网:http://www.sdhzyw.com
The above wonderful content is provided by Jinan Publicity Page Printer. I hope it will be helpful to you all. Welcome to our website: http://www.sdhzyw.com